Ignites with a 12 volt spark and burns with twice the temperature of oxyacetylene to cut, gouge or pierce any material in seconds.

Model: MAG3818™ Most popular for cutting
Style: Oxyflame tubes
Size: 3/8” x 18” (.9525 cm x 549 cm). 
Quantity: 50 per box
Weight: 19 lbs (8.6 kg).

Model: MAG1218™ Most popular for thick cuts.
Style: Oxyflame tubes
Size: 1/2” x 18” (1.5 cm x 549 cm). 
Quantity: 30 per box
Weight: 20 lbs (17 kg).

Model: MAG3836™ Most popular for piercing
Style: Oxyflame tubes
Size: 3/8” x 36” (.9525 cm x 1097 cm). 
Quantity: 50 per box
Weight: 38 lbs (17 kg).

MSDS

If you are looking for piercing power the MAG3836™ is a favorite among repair personnel and scrappers alike. Our exothermic plasma flame tubes are often referred to as hand held particle accelerators because of their ability to cut, gouge, wash, shape and more. They are useful for piercing long equipment pins. A 24” pin can be pierced and shrunk for removal in as little as 10 minutes (2 cutting tubes). Consider using a tube extender that comes in both 18" and 36" lengths to gain additional distance from the burn zone. This is particularly useful during challenging piercing situations. Convenient flame tube extender for additional reach comes in both 18" or 36" lengths.

Magnum's particle stream provides 10,000 degrees of cutting power to melt through anything, including stainless steel, cast iron, manganese, hard-facing, and even rocks. No preheating means a small HAZ (heat affected zone) This frequently translates into less problems with post metal fatigue. If you have ever cut a plate, re-welded it and had the plate crack next to the welds, you have experienced heat fatigue. This is why it is recommended that welds be stress relieved after plate cutting so as to relieve the internal pressures that have built up because of softening the surrounding metal with oxyacetylene gas. This is not a problem with our flame tubes which burn so hot and cut so fast there is actually less heat introduced into the material. Amazing but true.

Cutting and piercing stainless using new technology. Faster and far greater control. See video for more examples. Ten-thousand degrees can easily melt through stainless as the frame above shows. Merely press the tube against the steel and push. The flame does the rest. This process is quite handy for piercing through equipment pins.

Our deluxe ignition is a power booster with convenient prongs for igniting flame cutting tubes. The multi-purpose booster provides many functions. There is a handy recharger, battery status gauge and optional jumper cables to start your car, truck or welder. The charging socket also powers laptops, cell phones and work lights. The ignition comes with different battery configurations from extreme portability to rugged all day work duration. Click on the picture for additional information.

When piercing through thick materials like equipment pins, rocks or fire brick, a flame tube using an extender provides some distance from the operator to the burn zone. This distance keeps the blowback away from the operator and makes the pierce far more convenient. Horizontal pierces allow the magma to escape through the back side of the hole using gravity. A slow steady piece ensures a straight hole which is mandatory if piercing heavy equipment pins where collateral damage must be prevented. Tube extenders also allow for line of sight making it easier to keep the tube in the center of the hole. 

For 15 years Magnum has been providing cutting rods that cut longer with less sparks than a traditional cutting rods. The tubes have been deployed in every conceivable industrial setting. Our cutting tubes are also used in emergency rescue and tactical situations for breaching contingencies. 

Flame tubes are unique in that they cannot function separate from the system. Steel tubes are straightened and micro-coated to resist corrosion. They are subsequently filled with solid fuel spokes that can only combust in the presence of pure oxygen and an initial catalytic spark. Thus, flame tubes are quite safe and reliable. 

The outer tube and inner fuel are configured so that the inner fuel conforms to the inside of the tube in a corolla fashion so that a carburetor hole remains. Crimps hold the solid fuel spokes in position. The overall result provides a consistent burn for smooth cutting, gouging and piercing. 

Flame tubes fit into the torch head against a rubber washer. They are held in place by virtue of a brass collet. The arrangement is designed so as to prevent head leaks. Oxygen flows through the tube. A spark ignites the tip of the tube and inner fuel. Once ignited, no additional spark is required. The tube will continue to burn so long as oxygen pressure of ten pounds or more is present. 

A 2" recess in the rear of the flame tube ensures the flame will extinguish as it nears the torch head. This safety recess prevents flashbacks.  Flame tubes are ideal for repair, maintenance and situations where speed of cutting is important.

An example of a .375" cutting tube using oxygen as the sole gas to easily cut through 2" of plate. See the video for more examples. It takes a mere 12 volt spark to ignite a flame tube. Once ignited, the flame tubes burn without additional spark so long as positive oxygen flow is present. Flame tubes can burn with as little pressure as 15 pounds of oxygen for sheet metal. When oxygen pressure is increased, the flame length is also increased. High oxygen pressure can burn a hole through solid rock. When rocks get stuck in crushers, this is the handy tool to pierce and fragment such boulders to get production going again.

---

Consider ordering an oxyflame extender for additional reach.

Ordering:

1-800-957-4344 Toll Free.

1-760-868-6748 Alternate.

MAG3626™ 26 amp hour 36 volt welder

Welds on land or underwater using umbilical cables. Patent pending.

ROLLS ON WHEELS: Our MAG3626™encompasses a 36 volt DC welder that can also double as an ignition source due to the side cam lock adapters. The portable unit yields incredible welding power by virtue of its three 12 volt Osyssey® 26 amp hour dry cell batteries wired professionally to balance the load and provide the essential impetus to drive virtually any 3/32" or 1/8" electrode. Even .750 plate can be welded using this unit when the plate is properly beveled. Swapping the cables changes the welding polarity. This unit ships with a heavy duty ground clamp and 400 amp stinger handle.

• Heavy duty Pelican® case with wheels and pull handle.
• Three 12 volt 26 amp hour Osyssey® dry cell batteries.
• Three aluminum battery boxes secured to the Pelican® case.
• Two 500 amp cam locks for welding cable or torch igniter.
• 36 volt gauge and 36 volt charge port.
• 36 volt float charger with suitable connections.
• One heavy duty power switch.
• One heavy duty ground clamp.
• 10 foot of #4 high strand flexible AWS weld cable.
• One 400 amp insulated welding handle with twist lock jaws.
• Complimentary supply of 1/8" welding electrodes.
• Total shipping weight of system: 110 lbs.
• Ships UPS in one box.

Specify longer cables for underwater ignition and welding. Having a DC welder on hand is essential for civil defense, tactical response, emergency response, or any form of emergency repair and maintenance assignment where portability and dependable power are required.

Ac welders merely convert current to DC for the majority of welding with exception of TIG. Going straight to DC eliminates transformers, rectifiers, diods and more. The result is a portable welder with size selectable batteries that welds with minimal sticking. The polarity is reversed by switching the cables.

DC advantages:

• Easier stages.
• Fewer arc outages and sticking
• Less spatter for better looking welds
• Easier vertical and overhead welding.
• Smoother arc by virtue of direct flow current.
• DC reverse polarity (electrode positive) provides 10 percent more penetration at a given amperage than AC.
• DC straight polarity (electrode negative) welds thinner metals better.

How big a machine do I need?

• Most welding is done at currents lower than 200 amps.
• Small, portable welders suffice for most repairs.
• Large welders accommodate large electrodes.
• Multiple small welds are superior to single large welds.
• Thick materials can be welded by beveling the edges.
• Thick materials can be fused by using multiple beads.
• To change polarity reverse the red and black plugs.

What electrodes do I need?

• Small 3/32" electrodes are excellent for multiple passes.
• 6010, 6011, 6013, 7018 and 7024 are common electrodes.
• Flux characteristics influence speed, penetration and more.
• 6010 electrodes penetrate deeper than 6013 electrodes.
• 7018 yields better appearance, penetration and strength.
• Root passes use 6010 rod with cap beads using 7018.
• 7024 rods are "drag rods" capable of automatically maintaining the correct arc length due to thick flux, making it a favorite among repair and maintenance professionals.

Ordering:

1-800-957-4344 Toll Free.

1-760-868-6748 Alternate.

MAG9003™ three cylinder amphibian cutting system.

Introducing a pioneering breakthrough and the first of its kind. Over an hour of underwater cutting and almost two hours of land cutting from a single portable system. Remote control is the key. Operators control ignition via a button switch atop the ground clamp for the ultimate multi-tasking asset capable of cutting, gouging, piercing and even welding. Statistically, most underwater repairs are performed in less than twenty feet of water which falls well within the reach of the fifty foot of umbilical that ships with the system. As part of its integrated design, the new portable system not only performs from a solid platform, it also suffices as a flotation device in emergency circumstances.

Use the system for underwater repair, maintenance, salvage and scrap. For utility, the cylinders boast standard CGA540 fill valves for rapid filling at standard oxygen service locations. Each system ships completely operational once the oxygen cylinders are filled at a local welding gas supplier like Airgas or Air Liquide. Fifty cutting rods are included with the system which provide a significant cutting yield. For those situations when a welding machine is not practical, the unit can also double as a spot welder. Repair shafts, spot weld plates, fabricate brackets and much more.

A precision brass manifold connects all three cylinders for single use or multiple cylinder use, yielding over an hour of cutting. A remote solenoid activated ignition switch allows operator to close a topside switch for underwater ignition of flame cutting tubes. The 24 volt ignition boasts two Odyssey® 26 amp dry cell batteries for efficient underwater igniton. A new feature is the button switch atop the ground clamp. If a suitable ground is not found on the work material, a scratch plate a top the ground allows for efficient ignition. The entire unit is encased in a Pelican® case that can be carried or rolled to the work area.

Ships with:

One floatable Pelican™ case.
One Blackhawk™ cutting torch.
Fifty foot of umbilical assembly.
One 24 volt battery ignition complete.
One 24 volt solenoid fitted with cam lock adapter.
One box of oxyflame cutting tubes. 
Three 66 cubic foot 3000 psi oxygen cylinders.
Three 150 psi preset oxygen regulators.
Three CGA540 3000 psi oxygen cylinder valves.
Three 3000 psi oxygen gauges. 
Precision float charger for battery maintenance. 
Instructional video CD.

Very durable and reliable waterproof Pelican™ case.
The 50/50 lid to base ratio includes detachable lid. 
Flotation rating: 500 lbs. (227 kgs) in saltwater.
Fold down handles and metal padlock protectors.
Polyurethane wheels with steel bearings.
Weight: 175 lbs. total for entire system. 
External Dimensions: 46" x 26" x 17"

Box 1: System.

Box 2: Battery Ignition.

Box 3: Flame cutting tubes.

NOTE: Ships UPS in three boxes or one box by truck. 

All contents store in a heavy duty Pelican case for deployment from the shore, pier, inflatable and more. It rolls or has side handles for ultimate portability. A serious cutting and welding asset for both land or marine applications.

---

Consider an upgrade to our new 36 volt ignition - welder or spare composite cylinders for emergency response situations.

Ordering:

1-800-957-4344 Toll Free.

1-760-868-6748 Alternate.

MAG9000 Single cylinder tactical backpack cutting system.

Featured in Wired Magazine.

Breach 4" of plate in 4 seconds translates into dispatching a serious amount of steel in an hour on a single charge. Weighing in at a fractional 26 pounds, this lightweight backpack cutting system can be taken anywhere to cut almost any material in seconds. Consider the possibilities of sixty minutes of continuous cutting to melt through ferrous and nonferrous materials in seconds. Used by repair technicians, field dismantling mechanics, emergency rescue personnel and more.

The system uses safe consumables that can only burn using pressurized oxygen driven through their center once ignition has takenplace. Our unwrapped flame cutting tubes come in both 18" and 36" lengths for cutting, gouging or piercing in any position.

Tubes can be easily bent for access to difficult cutting areas often minimizing dismantling time. The longer flame tubes are a favorite among heavy equipment personnel for piercing and removing pins. With no preheating, the focused particle stream can burn through rust, scale, paint, slag and even limited layers of concrete.

M.S.H.A. and N.I.O.S.H. approved for mining applications.

Ships with the following:

• Two 3000 psi composite oxygen cylinders.
• Two CGA540 cylinder valves.
• Two preset 150 psi oxygen regulators.
• Cutting torch with thumb regulator valve.
• Oxygen hose with quick disconnect.
• Alice backpack with rubber cylinder straps.
• Deluxe 12 volt ignition system.
• Oxyflame cutting tubes.
• Oxyflame tube torch head extender.
• Additional reserve collets.
• Gloves and shade 5 glasses.
• Pelican heavy duty carry case.
• Universal float charger with adapter.
• Instructional CD.
• Shipping Weight: Approximately 125 lbs.

Patent pending.

Powerful 18 amp hour ignition lights oxyflame cutting tubes in two seconds and will easily provide well over 100 ignitions between charges. 

Dual oxygen tanks allow both cutting and breathing functions with a simple retrofit.

System can cut or double as emergency air pack for ultimate utility and safety.

---

Customers purchasing this item frequently purchase additional cylinders for emergency reserve.

Ordering:

1-800-957-4344 Toll Free.

1-760-868-6748 Alternate.

MAG3818X .375" x 18" Marine coated oxyflame cutting tubes.

MAG3836X .375" x 36" Marine coated oxyflame cutting tubes.

MAG1218X .500" x 18" Marine coated oxyflame cutting tubes.

MAG3626 36 volt igniter welder.

MAG0021 12 volt portable igniter.

MAG0024 24 volt portable igniter.

3000 psi Composite Cylinders

	1-800-957-4344 Toll free 1-760-868-6748 Alternate 1-760-868-6749 Fax Hours: 7:00 am - 4:00 pm pst
email	Veteran owned.

Back to Main Page